Civil Engineering Daily Quiz – Set 10 (July 12, 2025) Engineering Jobs and Engineering Solutions

1 votes, 5 avg

Civil Engineering Daily Quiz

Civil Engineering Daily Quiz

Civil Engineering Daily Quiz – Set 10 (July 12, 2025)

1 / 25

Category: Uncategorized

Which Primavera feature groups tasks that must be done sequentially?

A. Resources

B. Calendar

C. Activity Relationships

D. Role filters

2 / 25

Category: Uncategorized

What is the use of Feature Lines in Civil 3D?

A. Export points

B. Draw profiles

C. Print layouts

D. Define grading limits with elevation control

3 / 25

Category: Uncategorized

What does the “IF” function do in Excel?

A. Merges sheets

B. Returns all values

C. Filters data

D. Performs logic check and returns results

4 / 25

Category: Uncategorized

Which tool in Revit helps review interference between elements like duct and beam?

A. Clash detection

B. View template

C. Phase filter

D. Section box

5 / 25

Category: Uncategorized

In Primavera, what does “Float” indicate?

A. Resource count

B. Time flexibility without delaying project

C. Budget buffer

D. Delay penalties

6 / 25

Category: Uncategorized

In Primavera, what does “Float” indicate?

A. Budget buffer

B. Delay penalties

C. Time flexibility without delaying project

D. Resource count

7 / 25

Category: Uncategorized

In AutoCAD, what is the function of the “OFFSET” command?

A. Create parallel lines at a set distance

B. Hatch surface

C. Trim boundaries

D. Copy objects

8 / 25

Category: Uncategorized

What type of foundation is best for waterlogged soil conditions?

A. Raft

B. Pile foundation

C. Strip

D. Open trench

9 / 25

Category: Uncategorized

What does “modular ratio” represent in RCC design?

A. Ratio of elasticity of steel to concrete

B. Factor of safety

C. Ratio of loads

D. Strength of concrete

10 / 25

Category: Uncategorized

Why are cover blocks essential in RCC work?

A. Jointing

B. Load transfer

C. Maintain clear cover

D. Alignment

11 / 25

Category: Uncategorized

What does a high FSI (fineness modulus) of fine aggregate indicate?

A. High clay content

B. Coarse sand

C. Very fine sand

D. High water demand

12 / 25

Category: Uncategorized

Which IS code gives guidelines for general construction in seismic zones?

A. IS 456

B. IS 1893

C. IS 3370

D. IS 10262

13 / 25

Category: Uncategorized

Which test is used to determine the compressive strength of bricks?

A. Slump test

B. Impact test

C. Flexural test

D. Crushing test

14 / 25

Category: Uncategorized

What is the typical live load considered on a railway bridge per IS: 800?

A. 350 kN/m

B. 50 kN/m

C. 100 kN/m

D. 10 kN/m

15 / 25

Category: Uncategorized

Why are expansion joints critical in long span bridge decks?

A. For cable holding

B. To connect piers

C. To drain water

D. To accommodate movement from temperature variation

16 / 25

Category: Uncategorized

Which element transfers load from bridge superstructure to substructure?

A. Parapet

B. Bearing

C. Diaphragm

D. Deck slab

17 / 25

Category: Uncategorized

Which type of roller is best suited for compacting bituminous layers?

A. Plate compactor

B. Sheep foot roller

C. Tandem roller

D. Grid roller

18 / 25

Category: Uncategorized

Why are expansion gaps left between two RCC slabs in long corridors?

A. Reduce reinforcement

B. Allow thermal expansion

C. Save material

D. Facilitate curing

19 / 25

Category: Uncategorized

Which technique is used for accurate diagonals in square column layout?

A. Mason’s square

B. 3-4-5 method

C. Auto level

D. Plumb bob

20 / 25

Category: Uncategorized

What is the typical height of brick masonry for a single lift during construction?

A. 1.2 m

B. 3.0 m

C. 2.5 m

D. 1.8 m

21 / 25

Category: Uncategorized

Which equipment is commonly used for compaction of sand in foundations?

A. Plate compactor

B. Water jet

C. Vibrating needle

D. Trowel

22 / 25

Category: Uncategorized

Why are drip moulds provided below window sunshades?

A. To prevent water from running back to the wall

B. Attach grills

C. Provide thermal insulation

D. Aesthetic purpose

23 / 25

Category: Uncategorized

Which IS code provides guidelines for shuttering and formwork practices?

A. IS 875

B. IS 14687

C. IS 800

D. IS 456

24 / 25

Category: Uncategorized

What is the primary cause of segregation in concrete mix?

A. Excessive water

B. Using coarse sand

C. Adequate curing

D. Proper mix design

25 / 25

Category: Uncategorized

Which technique is commonly used to prevent shrinkage cracks in concrete during hot weather?

A. Over-vibration

B. Use of silica fume

C. Fogging and surface curing

D. Use of fly ash

Your score is

The average score is 67%

Anonymous feedback

For more Job Updates	Click here
Follow us on LinkedIn	Click here
Follow us on Facebook	Click here
Follow us on Twitter	Click here
Join on WhatsApp	Click here

Civil Engineering Daily Quiz – Set 10 (July 12, 2025)

Leave a Comment Cancel reply